This meme doesn’t include the other factor when living with other people that they might run a tap elsewhere in the house or flush a toilet
The hot water dial on my shower slowly turns itself off over there course of a shower, so I stick a latex glove between the dial and the tile so the friction keeps it from turning.
Take the handle off. There is a little collar that adjusts where the hot start/stops. Move it until desired range achieved. Takes a couple tries. Most contractors just leave it factory, which sucks. Some cities have regulations on how hot water can get when a house is sold too.
You forgot to mention that it’s dynamic and changes throughout the course of the shower based on how hot the water is in the tank 🤬
Sounds like you need to drain your tank and also should probably check the sacrificial anode while you’re at it.
Take the handle off and adjust it so the max is the right temperature
I have no idea why thermostatic mixer valves never caught on in most of the world.
Most showers here in Germany gave it nowadays, but they rarely put it in the faucets and the water in our apartment is steaming hot. Burned my hand more than once on accident.
This is too real.
Are thermostatic shower mixers not a thing where you guys live?
Nope. I hadn’t even heard of them until a few days ago, when someone from a different country than mine mentioned them, so I went searching the web to figure out what they were. I’m so jealous!
Mines just a valve that controls the flow of hot vs tap water, I know this for a fact cause I installed it myself. Mind you that doesn’t give away the daisy chained together nature of my water hook up but hey it works.
This is a thermostatic shower mixer. This is what happens when they seize up with limescale. This is not normal operation. The cartridge needs to be replaced.
Are you sure about that? I don’t see any numeric temperature settings. Every thermostatic mixer I have ever seen as at least a 38°C/100°F setting.
And also people are talking about the temperature creeping up during the shower due to the pipes heating up… That doesn’t happen on a thermostatic mixer.
But I guess limescale could seize it up… I have just never experienced that, and the water is very hard where I live…
This was my favorite thing about visiting Europe, and no, most Americans have no fucking clue what that is.
Just because it doesn’t have temperature markings doesn’t mean it can’t maintain a constant temperature (selectable from a wide band). These are mechanical devices without any electronics. They work by maintaining the pressure ratio you set between the hot and cold supplies. When they seize up they become “100% cold or 100% hot, no in between” devices. In other words, a cold/hot toggle switch.
The ones I’m talking about doesn’t just keep the pressure ratio static, they actually adapt to the temperature of the hot and cold water.
If the hot water drops in temperature, then the output water stays at the right temperature, but the output pressure might drop, as the mixer allow more of the hot water through, and less of the cold water.
Of course if the hot water drops below the set temperature, it can no longer maintain it’s temperature.
And yes these are also entirely mechanical, no electronics or even electricity.
My apartments hot water supply is really hot, so the band is still pretty narrow.
All hot is about 60° C, so you need comparatively little hot water, at least in relation to every other place I’ve showered…
That’s not all. Once you get the temp just right, the plumbing starts to heat up and the temp changes gradually over the course of the shower, so you have to adjust it as you go.
Also the hot water layers in the hot water tank
My shower has a thermostat and I can just set the temperature and go.
You bastard! I am so deeply jealous!
And to make it worse is like you are playing over the most laggy connection ever.
The only thing with more latency is IPoAC
ITT: people without infinite hot water either from a tankless heater or stadsverwarming
The sweet spot for my shower can be found by tapping the handle up or down with less force than a mouse click, like I think this moves it a micrometre.
Exactly how I do it. I start it running for a few second in the general middle spot, and tap it either way. It’s going to vary where that is summer or winter, but fortunately the handle isn’t too tight and I can get it with a few taps.
I had one shower in an apartment where the temp was set by twisting the round knob, but turned on by pulling out the whole thing. Perfection.
Of course no one has ever done this joke better than Suzy Izzard
Thank you for posting this so I didn’t have to. Genuinely every time I struggle to get a shower to the right temperature (so, you know, every time I shower) I hear this bit in my head.
Also, I didn’t realise she was going by Suzy now. Good for her!
Single, quick-turn handle shower/bath spigots work alright for places with giant hot water boilers, but not so much for single family residences. I want to control the flow of both temperatures separately and accurately.
I used to think I wanted that until I had to use separate knobs for hot and cold water and it was even more fiddly, you also have to get pressure correct. They ended up leaking and I figured it was just easier to replace with a turn handle fixture that uses cartridges than learning how to repair super old plumbing, the handle is actually way more forgiving in terms of getting it in the range of tolerable temperatures, and you don’t have to think about water pressure.
Just turn on the hot water first to desired pressure, then turn on the cold water to get temperature
Edit: because you really don’t need much cold water to cool it down.
Edit 2: then as the shower cools down over time, just turn down the cold water a little bit as needed
Edit 3: and because you’re able to control overall pressure, you can have exact temperature to a trickle or full power, allowing you to have as long or powerful of a shower as you want
